Centralina Correzione errori frecce LED

SKU 31-0190
0/5
Previous
Next

Monti le tue nuove frecce led sulla tua moto e questa ti segnala che un indicatore è fulminato perchè non arriva abbastanza assorbimento

questa centralina ti permette di correggere questo tipo di errori con l'output regolabile in 50 intensità diverse.

disponibile in 3/5 giorni lavorativi

PERCHÈ ACQUISTARE SU DUSTY WHEELS

PAGAMENTO

Accettiamo bonifici e pagamenti tramite Paypal/Carte di credito.

SPEDIZIONE CON CORRIERE NAZIONALE

La spedizione arriverà in 24/48 ore dalla disponibilità della merce.

MIGLIOR PREZZO GARANTITO

La miglior scelta per una buona qualità.

Descrizione

Monti le tue nuove frecce led sulla tua moto e questa ti segnala che un indicatore è fulminato perchè non arriva abbastanza assorbimento

questa centralina ti permette di correggere questo tipo di errori con l'output regolabile in 50 intensità diverse.

è ottimo anche come diagnosi per capire che tipo di resistenza utilizzare per poi applicare quella corretta senza effettuare ulteriori tentativi

non mettere vicono le fonti di calore

disponibile in 3/5 giorni lavorativi

Descrizione originale

You know how it goes: you got these beautiful new LED turn signals for your motorcycles but since then, the flashing speed is no longer correct, the ECU is reporting errors concerning the flasher relay, says that your turn signal is broken or is simply not strong enough for your turn signals. And now, you have to order different load equalisers and test them on your motorcycle until you find the one with the right value...

However, a resourceful Louis employee found a way around this: our new, digitally adjustable equaliser that has 50 adjustable power values. The Vari Load is simply clamped to the turn signals and the necessary load is simply set via the blue "programming cable".

The power of the Vari Load is changed by the thin blue cable. Just hold the blue cable against + 12 volts (red) cable and the load will slowly increase in 50 steps up to about 10 watts. If you hold the blue cable against ground cable (black), the load is reduced until it is at 0 watts. Once you disconnect the cable from one of these two cables, the set load value will be saved and recalled the next time you turn it on. A complete run of all retrievable power values ‚Äã‚Äãtakes about 20 seconds. The built-in LED thus flashes up to 50 times when the power value changes and indirectly indicates the set value by its number of flashing lights. As soon as one of the two limits (0 watts or approx. 10 watts) is reached, it lights up permanently.

Incidentally, the Vari Load is also a cool tool for your workshop and a must in every toolbox. You can easily set the necessary load for the flasher relay via the device and then replace it with the required resistance value, that you can find in the table on page 2 of the installation instructions.

  • Dimensions:56 mm x 36 mm x 17 mm without fastening straps
  • Housing:Black ABS, cast with 2-component potting compound
  • Input voltage: 8 - 15 volts
  • Connections: program cable 0.14 mm¬≤, power section 0.75 mm¬≤
  • Installable load range:Between approx. 2 x 1 watt and 2 x 10 watt in approx. 0.2-watt increments
  • Maximum ambient temperature: 90 degrees Celsius

The Vari Load can produce loads up to 10 Watt, other devices mostly only up to about 1 Watt, what in many cases is much too low if you want to change the old halogen bulbs for LEDs. The Vari load is very easy to understand and configure to your project. The Vari load is waterproof.